Fireye | BurnerPRO

ADD NEW FUNCTIONALITY TO BURNERS WITH THE SIEMENS LFL OR LGK INSTALLED. THE FIREYE BURNERPRO OPERATES AND CONTROLS YOUR BURNER THE SAME WAY AS YOUR LFL OR LGK DOES BUT WITH THE ADDED BENEFIT OF:

• Smart LED's showing current burner state
• 62 different lockout codes using the LED's to tell you exactly what the problem is so you can fix it quicker.
• Run / Check feature to allow the cycle to pause in the ignition, pilot or main timings. this allows easier commissioning and fault finding
• In check mode the LED's become a flame strength meter. This allows for aiming of the UV cell or realignment of the ionisation probe
• Built in self checking circuit for ionisation rod, this upgrades your burner to >24hr continuous use.

The Fireye BurnerPRO is a compact, microprocessor based, primary flame safeguard control system designed to provide the proper burner sequencing, ignition and flame monitoring for on-off, multi-stage, or modulating burners used in commercial heating and process equipment firing oil and gas fuels. The BurnerPRO flame safeguard offers two built-in amplifiers, which allows for use in UV only, FR only, and UV+FR applications. Flame monitoring for UV is accomplished by using available UV scanners: UV90L & UV1AL. Flame monitoring for FR version is accomplished by using available ionisation rod: 69ND1.

The FR amplifier circuitry is subjected to permanent self-checking, which allows it for use in applications that require burner cycle that runs for more than 24 hours. When operated as a UV control, the system is considered non-permanent, which requires a burner recycle at least once every 24 hours. Control functions and timings are factory set via unique micro-controller firmware. Through seven SMART LEDs, the control provides current operating status and lockout information in the event of a safety shutdown. Refer to the BurnerPRO ordering information section in this document for the various combinations of control functions and timings.

A complete BurnerPRO system includes the BP110/230, flame scanner and wiring base. The BurnerPRO performs a safe-start check on every burner cycle. If flame is detected prior to a start or during the purge cycle, the fuel valves are not energised and the control locks out. The ‘POC’ input is also monitored to verify that the main fuel valves are always in the proper state prior to the start of a burner cycle. The LEDs & alarm terminal are used to annunciate the presence of a lockout condition.

• Non-volatile lockout capability 

• Proof of fuel valve closure 

• Air-flow proving 

• A run/check feature allows the operator to stop the program sequence in different positions (Purge, Ignition, PTFI and MTFI) for system troubleshooting 

• Remote and local Reset 

• Two built-in amplifiers (UV, FR, UV+FR) for flexibility in applications 

• Smart LEDs provide on board diagnostic lockout information 

• Real-time internal diagnostics for added safety integrity 

• Extended temperature operation (-40°C to 60°C) with an over-temp inhibit feature 

• High capacity relay contacts 

BP-1002

CE Certificate

Supply Voltage:

BP110 110 VAC (+20%, -15%) 50/60 Hz, single phase 
BP230 230 VAC (+10%, -15%) 50/60 Hz, single phase 

Power Consumption:

7 VA 

Temperature Rating:

Operating: -40°C to +60°C (-40°F to 140°F) 
Storage: -50°C to +85°C (-58°F to 185°F) 

Flame Amplifier Rating: 

UV: Terminals 22 & 23, 300VDC 3mA(max)
FR: Terminals 24 & Earth, 330VAC (max), 3uA min/10uA max flame current

Protection Category:

IP40 standard version (with exception of wiring base) 
IP44 for “F” version 

Control Dimensions:

With wiring base (60-2944-1); 4.15” L x 4.15" W x 5.0" H (105mm x 105mm x 127mm) 

Shipping Weight:

Approx. 2.5 lbs. (1.13kg)